Fender rolling in NJ Central preferred

[Staszek]

So my new rear wheels will be 265/30R19 with a 40offset.

I was running 235/40R18's on BBS CH's which have a 35 offset which probably puts me very close to where the 19's will come out.

I am running the ZHP suspension, the 235's with the BBS's never rubbed and actually they are slightly taller tire then the the 265's are.

I am still worried that I may have a bit of a problem, so if I do, where is the best place to get fenders rolled. Experienced place.

[shogun]

yeah me too..i'm looking to go the 265 route...

please anyone with good personal or close personal experience only!!

not enough tire co. make 255's!

[Jeff43]

it's more up north, but Rogue in Hohokus did mine for me last summer. Ben uses the rolling tool (basically an arm that bolts on to your rotor w/a urethane wheel that presses against the fender lip); he takes the time to heat the paint on the fender so it is more pliable and will not crack under the pressure. i watched the entire process and he was very thorough through out. cost was $150.

www.rogueengineering.com

the trip to Rogue is worth it just to see whatever project their working on... :thumbup:

[shogun]

VERY COOL! i was there the other day...didn't know they did that!

thanks for the info.:thumbup:

[e46craze]

the trip to Rogue is worth it just to see whatever project their working on...

I agree :thumbup: but Staszek, try Jake at Freedman Tire on Rt. 27

732.985.2211

[Staszek]

the trip to Rogue is worth it just to see whatever project their working on...

I agree :thumbup: but Staszek, try Jake at Freedman Tire on Rt. 27

732.985.2211

Thanks!

[e46craze]

Thanks!


no problem..I'm most likely going there soon to have my fenders rolled

[Staszek]

no problem..I'm most likely going there soon to have my fenders rolled


Cool let me know how much!

[DMXtremeZHP]

chris... tell me when you go to rogue.. maybe you could also swing by my place and get the gruppe from me.. pm me

[Straz M3]

I'll be at Rogue tomorrow at Noon rolling my fenders and slapping the new Iforged rims on...if anyone wants to roll I will be there.

[Jeff43]

I'll be at Rogue tomorrow at Noon rolling my fenders and slapping the new Iforged rims on...if anyone wants to roll I will be there.

maybe i'll swing by at lunch to say hello and check out the new wheels... :thumbup:

[Straz M3]

Sounds good my man...I just saw your message on the other thread. I was "home" last week for Spring break but never actually went home...I was in Cancun Mexico for the week...definately stop by around 12...I cant be there for too long, I have an interview in NYC at 3

[Jeff43]

cool...my office is about 5 minutes away so i'll check in around noon...and i'd have been disappointed if you spent your spring break at home... ;)

-J

[JCz04Bimmer]

Jake at Freedman. Bar-none... the best. The guy who does it, Jamaican accent I think, is fantastic.

[e46craze]

Jake at Freedman. Bar-none... the best. The guy who does it, Jamaican accent I think, is fantastic.

J-

I know exactly who you are talking about...lol :thumbup:

[DMXtremeZHP]

ill come and swing by rogue if i have a car... my car wont be ready til tomrrow afternoon :bawling: i miss my car...still at C&D

[Synchromesh]

if i get my fenders rolled on my 325xi would i b able to fit 19s?

[steelblue46330i]

if i get my fenders rolled on my 325xi would i b able to fit 19s?

You can fit 19's on your car anyways. Its just that on sedans the widest you can go in the rear is I believe 255 without fender rolling.

[DMXtremeZHP]

how much would it be to roll fenders at rogue? specifically a e36 m3

[tweeeker]

Freedman Tire in Edison. Ask for Jake, tell em Rob from German Car Shop sent you. :thumbup: ....he does all out tires, alignments etc..... I'll prob be rolling my fenders in a few months and thats the man that will be doing them.

[Jeff43]

how much would it be to roll fenders at rogue? specifically a e36 m3

i'm guessing $150, the same as an e46...

[DMXtremeZHP]

thanks jeff