E46Fanatics - View Profile: MITE46 E46 BMW Social Directory E46 FAQ 3-Series Discussion Forums BMW Photo Gallery BMW 3-Series Technical Information E46 Fanatics - The Ultimate BMW Resource BMW Vendors General E46 Forum The Tire Rack's Tire Wheel Forum Forced Induction Forum The Off-Topic The E46 BMW Showroom For Sale, For Trade or Wanting to Buy

Go Back   E46Fanatics > Members List

MITE46 MITE46 is offline

Registered User

Visitor Messages

Showing Visitor Messages 1 to 10 of 15
  1. reedley330i
    09-08-2015 03:14 AM
    If you live in Ca how did you get your modded car past the DMV? Thanks!
  2. spike9075
    01-28-2014 03:12 PM
    hey read up on your forum! i am having one same problems as yours, i am only getting 4volts on my fuel filter rather then the 12 said i should be getting. i have a bmw 330ci and am desperatly trying to get this fixed. i notice you said you replaced the EKP module to get the fuel pumping again. just trying to figure out where this is located so i can try replacing it.
  3. dylan323i
    05-13-2012 07:34 AM
    thanks so much for leaving the site up man! its been such a huge help, i havent even touched a bmw m3 e46 and i pretty much know what im suppose to do thanks again man
  4. lovnblack
    04-20-2012 08:21 PM
    hi again, hope you would visit your profile/inbox in next day and see my this message. Im in trouble and a lot of stupid serviceman waste my days. Please help me or show me a way....the problem is O2 post cat sensor's female plugs are doesnot exist on my car. Sound weird maybe, let me explain..I am living some problems about injection time (3rd injector's ms timing is not zero or in average timing range, its raise up to 2ms and later my car engine start to shaking, my fuel consumption is not stable) cause of that want to try montage post cat O2 sensors on my new header's cat. (my car's first owner has removed this 2pcs O2 long sensors from catalitic conv.) and I started to search&find these 2 female plugs/signal cables for connect 2pcs O2 bosch sensors (990mm length cables) but there is no plug no cutted cable etc. Im already using 2pcs pre cat sensors (short cables) I follow their plug signal cables and lead to control unit DME box, I think long O2 sensor cables also must lead to control unit box right? If it is true, then I need buy used female cables and montage it onto right pins of control unit...but how? What I need, a schema, diagram or a drafting? which color cable, which pin etc...I could not find any document, schema or forum topic about it. I know that you are a great person about BMW, please help me, in last 2 days I visit a few serviceman and you really dont want to know their stupid comments! Hope you can show me a way. Best regards, Rifat
  5. zcchen
    04-18-2011 04:07 PM
    I am totally amazed by ur S54 transplant thread. Thank you for taking the time to document it for the community.
    I was going to SC my 325 but after reading your thread, I think I am going to do a S54 into a e46 sedan swap this summer.
    I am going to use a 6spd instead of SMG, so hopefully that makes it easier.
    But I have several questions that have been bothering me and you seem like the perfect person to go to.
    Did you swap out the whole harness? Did u put in the whole m3 harness? Or did u integrate m3's DME into the stock sedan harness? If so, how was it done? Any splicing of the harness?
    Thank you and look forward to hearing from you.
    My email is zcchen.e46@gmail.com
  6. e46rage
    02-23-2011 11:06 PM
    I was wondering if you can still make the wire for the smg wheel to retro fit it to my step. 330ci ?
  7. BlackPearl_Custom
    02-10-2011 01:13 PM
    hi! i read some threads about retrofitting e90 steering wheel on e46.. and told that you have done it before. so, i assume it is possible to fit e90 steering wheel on e46, and the question is what mods have to be done to do this mod?

    thanks alot mite46
  8. MITE46
    09-07-2009 04:49 AM
    the total cost has dropped quit a bit, you can get E46 M3 engine for <3k on ebay now. It's much easier if you do a 6speed swap,....no DSC to worry about
  9. MITE46
    09-07-2009 04:45 AM
    main problems with the swap were with SMG and DSC...they need to match perfectly for it to calculate the shifts properly.
  10. MITE46
    09-07-2009 04:44 AM
    M3 wheels will fit on the sedan but because of the offset it willl rub like crazy...20's will work if the offset is correct.


Total Posts
Visitor Messages
General Information
  • Last Activity: 03-23-2016 02:06 PM
  • Join Date: 09-18-2002
  • Referrals: 17


Showing Friends 1 to 4 of 4


Member Profile Recent Ratings
Feedback Score:
Positive Feedback:
Members who left positive:
Members who left negative:
Total positive feedback: 1
View all feedbacks for MITE46
6 Months
12 Months
Positive Positive 0 0 0
Neutral Neutral 0 0 0
Negative Negative 0 0 0

All times are GMT -5. The time now is 04:58 AM.

Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
(c) 1999 - VerticalScope Inc. All rights reserved.