E46Fanatics

E46Fanatics (http://forum.e46fanatics.com/index.php)
-   Australia (http://forum.e46fanatics.com/forumdisplay.php?f=48)
-   -   2000 E46 318i pipe connector (http://forum.e46fanatics.com/showthread.php?t=827061)

jcjdavis1 03-03-2011 06:47 AM

2000 E46 318i pipe connector
 
Hi. This is worth checking on the rear of the engine block, M43 engine -
http://i66.photobucket.com/albums/h2...BovaBob005.jpg http://i66.photobucket.com/albums/h2...BovaBob004.jpg http://i66.photobucket.com/albums/h2...BovaBob006.jpg
Was loosing water and touched this and it just broke off. Jim

Goondaddy 03-03-2011 08:27 AM

I had that same part break off when I had the M43 engine back in the day when I owned my e36. Worth checking!

Mitch E46 03-03-2011 02:21 PM

Holy sh*tttt

shannon1 03-03-2011 03:18 PM

Wow thanks for that, will have to check out mine.

How many km's/miles has your car done jcjdavis1?

jcjdavis1 03-03-2011 04:48 PM

Quote:

Originally Posted by shannon1 (Post 12879368)
Wow thanks for that, will have to check out mine.

How many km's/miles has your car done jcjdavis1?

Hi. Just over 113000mls. Jim

anf 03-03-2011 06:29 PM

jeebus!

where did u buy the replacement part from?

exil3 03-06-2011 10:22 PM

Yeah, mine corroded recently too, though it wasn't as bad, thankfully.
Check the o-rings within the hose connections while you have it apart as mine were pretty much non existent.

I sourced my replacement part through ASV/Euro car parts here in Adelaide for around $35 but the dealer asked $85-90!

vwikit 03-07-2011 07:10 AM

they are such a pain to replace aswell, if in perth see lintrex cost me $8

jcjdavis1 03-07-2011 12:13 PM

Hi. Part was 7. part No. 11 53 1 708 808. http://bmwfans.info/...attached_parts/ .Take the Pollen filter housing off after that it is down to feel. Tools required are short 10mm spanner and long screwdriver to unclip coolant hose and 1 jubilee clip on coolant hose, which you can see if you stretch over from drivers side,you do not need to take off the ccv hose.
I found it easier to lay on top of the engine and use two hands to get at the 2x10mm bolts, just take your time and don't drop anything. Take the hoses off first and put them on last.
Make sure you get the old O ring out when taking the old connector off, new connector has an O ring fitted.
You will loose coolant so make sure and bleed the system after topping up to avoid air locks. Jim

129c 02-14-2013 01:47 PM

Changed this part on my 318ci today because when i removed the small hose the plastic tube broke off. There is very limited room and if you drop the 10mm bolts you have a problem unless it falls nicely!

Heres a picture with the new part fitted.

http://img820.imageshack.us/img820/3387/partar.jpg _sl_ _sl_


All times are GMT -5. The time now is 02:50 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
(c) 1999 - 2011 performanceIX Inc - privacy policy - terms of use