E46Fanatics

E46Fanatics (http://forum.e46fanatics.com/index.php)
-   Engine & Performance (http://forum.e46fanatics.com/forumdisplay.php?f=36)
-   -   E46 325 09.03+ 325i Manual Transmission S5S 250G 22 tooth (http://forum.e46fanatics.com/showthread.php?t=956733)

2.5-12 11-19-2012 09:54 AM

09.03+ 325i Manual Transmission S5S 250G 22 tooth
 
this is a Getrag 250 trans from a september 03+ 325i/iC. under 50K miles on it. shifts like brand new. BMW wants over $3k for this transmission new.

this tranny is unique to the 04-05 model years (06 convertible) because of its 22 tooth input shaft which uses the same clutch as 90% of late model 6 speed BMWs instead of the 10 tooth which had been produced from 1991 till 2003.

this is a rare transmission, clutch kits are available searching 2004 325i 22T

will physically bolt to any M50 M52 S50 S52 M52TU M54 M56 N52 M42 M44 or M40 engine (may bolt to others as well.)

asking $350.

actual trans, 22T shaft.
https://lh4.googleusercontent.com/-P...0%252B0000.jpg

reference photo, identical to:
http://i395.photobucket.com/albums/p.../E30age080.jpg

2.5-12 11-27-2012 09:56 PM

bump

Bmw0224 11-27-2012 10:15 PM

Where are you located?

2.5-12 11-27-2012 10:16 PM

Minneapolis, MN.

right above my post count, too.

Bmw0224 11-28-2012 03:19 PM

I would of bought it but I'm all the way in Cali

2.5-12 11-28-2012 03:33 PM

no worries, PMs replied -- I am willing to ship this guys. costs between 80 and 100 to lower 48 states.

Thanks!

2.5-12 11-29-2012 09:56 PM

rumpitybump

Eric W 12-02-2012 10:59 PM

So if I had a 2002 5-speed 325ci build date 04/2002 this transmission would be a direct bolt on swap into my car except for me having to buy the correct 22T clutch and flywheel for it????

2.5-12 12-02-2012 11:02 PM

yes the trans is identical to the 2002 trans except for the input shaft.

buy the right clutch setup and you're golden.

Eric W 12-02-2012 11:08 PM

Okay let me do some research on this. My current tranny's input shaft bearing is slowly going out, but I just dropped a ton of cash on the UUC. E34 M5 clutch setup an single mass flywheel. not sure what to do at this point,: Fix or replace the tranny

2.5-12 12-03-2012 11:58 AM

sounds good

2.5-12 12-04-2012 08:32 PM

bump

2.5-12 12-05-2012 10:30 PM

bump

2.5-12 12-10-2012 01:36 PM

bump

2.5-12 12-12-2012 01:18 PM

bump

2.5-12 12-16-2012 03:01 PM

bump

2.5-12 12-18-2012 10:51 AM

bump

zha50 12-19-2012 05:03 PM

I may need this if I cannot fix my current one, cracked it at the drain plug. ... they are hard to find :(

2.5-12 12-19-2012 05:28 PM

Quote:

Originally Posted by zha50 (Post 14994223)
I may need this if I cannot fix my current one, cracked it at the drain plug. ... they are hard to find :(

just keep me apprised, they are unreasonably difficult to come by, for sure.

zha50 12-19-2012 07:37 PM

Problem is just not in the same country. Might be too difficult to ship. First point of call is welding, then trying to source a used one locally first.


All times are GMT -5. The time now is 09:44 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
(c) 1999 - 2011 performanceIX Inc - privacy policy - terms of use