E46 BMW Social Directory E46 FAQ 3-Series Discussion Forums BMW Photo Gallery BMW 3-Series Technical Information E46 Fanatics - The Ultimate BMW Resource BMW Vendors General E46 Forum The Tire Rack's Tire Wheel Forum Forced Induction Forum The Off-Topic The E46 BMW Showroom For Sale, For Trade or Wanting to Buy

Welcome to the E46Fanatics forums. E46Fanatics is the premiere website for BMW 3 series owners around the world with interactive forums, a geographical enthusiast directory, photo galleries, and technical information for BMW enthusiasts.

You are currently viewing our boards as a guest which gives you limited access to view most discussions and access our other features. By joining our free community you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is fast, simple and absolutely free so please, join our community today!

If you have any problems with the registration process or your account login, please contact contact us.


Go Back   E46Fanatics > Search Forums

You searched for the keyword(s):
Your search results are listed below. If you did not find the answer you were looking for, please try searching again. Make sure that you are searching the entire site and not a specific forum. If you cannot find the answer to your question, create a new discussion topic in the appropriate BMW related or Off-Topic section.

Showing results 1 to 16 of 16
Search took 0.30 seconds.
Search: Keyword(s): ; Posts Made By: Silver02
Forum: BMW News from around the Web 03-27-2013, 06:01 AM
Replies: 90
Views: 21,001
Posted By Silver02
Ewww... that looks like a Ford Probe

Ewww... that looks like a Ford Probe
Forum: General E46 Forum 03-11-2013, 08:27 PM
Replies: 9
Views: 477
Posted By Silver02
Thanks for the replies. I checked the nut...

Thanks for the replies.

I checked the nut torque while supporting the inner ball joint with a jack. No problem there. Replacement arm is in the mail, so hope to get this resolved soon.
Forum: General E46 Forum 03-10-2013, 04:39 PM
Replies: 9
Views: 477
Posted By Silver02
Meyle CA ball joints loose after only 33k miles

Been noticing a clunk from the front end when going over bumps. After poking around, I can see the ball joint is loose and jiggles up and down when I shake the brake rotor. I installed these 33,000...
Forum: DIY: Do It Yourself 03-03-2013, 08:47 AM
Replies: 1
Views: 482
Posted By Silver02
Got everything back together. It does seem...

Got everything back together.

It does seem like the car sits a bit higher now, but maybe that is OK. I think the new Koni struts are the right ones but the issue is the OEM struts do not fully...
Forum: DIY: Do It Yourself 03-02-2013, 02:35 PM
Replies: 1
Views: 482
Posted By Silver02
RTH - Koni sport strut longer than OEM

Real Time Help

Guys,

Need your help. I am part way into replacing struts on a 2002 325i with sport package. I've pulled the first strut and am getting ready to put everything back together and...
Forum: General E46 Forum 01-22-2013, 08:33 PM
Replies: 2
Views: 282
Posted By Silver02
Removal thread might get you started: ...

Removal thread might get you started:

http://www.e46fanatics.com/howto/howtodetail.php?howto_id=40
Forum: General E46 Forum 09-01-2010, 01:31 AM
Replies: 5
Views: 884
Posted By Silver02
I am in the same boat with 125k on the clock. I...

I am in the same boat with 125k on the clock. I decided to go with the full bimmerworld kit (http://store.bimmerworld.com/bimmerworld-e46z4-front-suspension-overhaul-kits-p1415.aspx) including CA,...
Forum: General E46 Forum 06-06-2010, 06:13 PM
Replies: 8
Views: 620
Posted By Silver02
Thanks, I'll get a few pictures together and post...

Thanks, I'll get a few pictures together and post up.



It seems like the housing gasket is the most likely candidate. It's on my todo list but I think I might let the Houston summer pass...
Forum: General E46 Forum 06-06-2010, 09:03 AM
Replies: 8
Views: 620
Posted By Silver02
I replaced the oil pressure switch today on my...

I replaced the oil pressure switch today on my M54. I was a bit worried when the I read in the Bentley manual "In some engines, access to the oil pressure warning switch port may be extremely...
Forum: General E46 Forum 05-16-2010, 08:59 PM
Replies: 8
Views: 620
Posted By Silver02
Thanks for the replies. No codes are being...

Thanks for the replies. No codes are being thrown, no CEL.

I haven't tried to pull out the broken piece yet, so don't know how many pins.

The oil pressure sensor is a good suggestion. I'll...
Forum: General E46 Forum 05-16-2010, 02:20 PM
Replies: 8
Views: 620
Posted By Silver02
Help identifying loose electrical connector

Hi all,

I found a dangling wire today when changing the oil. It looks like the wire and sensor broke off of something. Any ideas where it came from and what I need to do to fix it? Thanks....
Forum: General E46 Forum 12-27-2009, 10:01 PM
Replies: 79
Views: 5,226
Posted By Silver02
I feel your pain brotha. With my 2002 325i, the...

I feel your pain brotha. With my 2002 325i, the problems come in fits and spells, so get if fixed and hopefully the POS car will take it easy on you for a while.
Forum: General E46 Forum 08-27-2009, 07:54 PM
Replies: 5
Views: 554
Posted By Silver02
Ummmm.... WTF is a Strong Strut?

Ummmm.... WTF is a Strong Strut?
Forum: General E46 Forum 08-20-2009, 05:57 PM
Replies: 36
Views: 6,944
Posted By Silver02
One additional note that may save you some...

One additional note that may save you some frustration is the label on the DSC has several sets of numbers on it, none of which are the whole BMW part number. I was able to read the numbers 59704...
Forum: General E46 Forum 08-20-2009, 05:12 PM
Replies: 36
Views: 6,944
Posted By Silver02
I recently went through this excercise on my 02...

I recently went through this excercise on my 02 325i.

First, get the right part number for your DSC controller:
This required removing the side cover like you did before, then using a dental...
Forum: General E46 Forum 07-24-2009, 09:01 PM
Replies: 8
Views: 8,698
Posted By Silver02
Need to recode?

Did you have to recode the controller? I'm thinking about replacing my faulty unit DIY but don't know how to recode. Is this necessary?
Showing results 1 to 16 of 16


 

All times are GMT -5. The time now is 08:02 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
(c) 1999 - 2011 performanceIX Inc - privacy policy - terms of use