View Single Post
Old 09-22-2010, 04:11 PM   #1
Wesley Snipes
Registered User
 
Join Date: Sep 2010
Location: nj
Posts: 0
My Ride: BMW Power
FS/FT: E36 M3 track car

i have previously listed this car under another name but i cant get into that account so i made a new one. so dont be sketched out that this is my first post.

i will also trade for an E46 M3. 6 speed only pref stock.

heres the info, there is ALOT done to this car so i am going to try and remember everything.

i am the 2nd owner of this car and bought it bone stock! first owner was an older gentleman.

1999 M3
145k
titan silver

modifications will be broken down into sub categories:

1. ENGINE
-Active autowerke race header
-Active autowerke race exhaust (with MANY custom configurations)
-UUC lightweight pullies
-m50 mani with bimmerworld kit and all new gaskets
-intake
-SPAL 16" puller race fan
-NO A/C
-custom catch can setup
-alum t stat housing
-low temp t stat
-all t stat gaskets
-OEM waterpump
-OEM radiator
-custom coolant reservoir
-10w-60 castrol/oem filter oil changes
-re-done engine harness (deleting all un used stuff, EVAP, fogs, etc looks clean!)
-all new coolant hoses
-all new power steering lines

2. SUSPENSION/MOUNTS
-bilstein gruppe N coilovers
-Hyperco 650# springs
-Bimmerworld camber shim kit
-OEM upper strut mounts
-TMS 60mm upper spring perches
-TMS rear strut mounts
-TMS sway bar set
-TMS rear end links
-Bimmerworld Front endlinks
-AKG 95D control arm bushings
-OEM lemfoerder tie rods
-OEM lemfoerder control arms
-*** front wheel bearing/hub
-*** rear wheel bearings
-AKG 95d subframe mounts
-FULLY reinforced rear subframe which includes swaybar and bushing cup reinforcements as well as seam welding for added strength
-TMS lower fully adjustable camber arms
-fully reinforced upper spring arms (gusseted)
-OEM rear upper/lower outer balljoints
-OEM gruppe N upper inner control arm bushings
-UUC rear trailing arm bushings
-TMS aluminum/delrin diff bushings
-cleaned/painted/sandblasted 3.23 diff
-UUC full magnesium strut bar
-Vorshlag nylon motor mounts
-Vorshlag race trans mounts
-EVERY SINGLE BOLT on the entire suspension front and rear has been replaced with brand new hardware from the dealer!!!!!
- Azevedo Short shift kit with the stainless spacer to make the shifter higher

3. BRAKES
-stoptech cross drilled rotors
-OEM rebuilt calipers
-TMS brass caliper guides
-Hawk ceramic pads
-TMS stainless coated brake lines
-front and rear Bimmerworld caliper pistons
-Bimmerworld 92mm race studs
-Bimmerworld race lugs (black)
-Bimmerworld 12mm front spacer
-ATE super blue fluid

4. INTERIOR:
-chassis was stripped bare (no sound deadening, etc)
-no heat
-LTW headunit block off with STACK gauge and fan switch
-MOMO race wheel
-quick release hub
-no airbags
-1 RED sparco speed seats
-entire interior is not in the car but i do have alot of it (still have entire interior except door cards and vaders)
-BMW motorsport shift knob

5. Wheels
-17x9 et 41 CCW Classics (shot peened, race version)
- front tires as of now are 235-40 azenis
-rear tires are 255-40 azenis

by the time the car is sold it will most likely have 255's up front and a bolt in 4 point cage.

there is SOOOO much more im sure but i am doing all of this off of my memory.

compression test showed 190-195 across all 6.


$17,000 with everything included with the car. this is a ready to go track car. the car handles amazing and it is by far the most solid car i have ever had or been in. the car is really something else as far as handling goes.

email is mpower0324@gmail.com

thanks for taking the time to look and i will update the thread as i remember more.

ALSO: everything is documented! all receipts and everything!




















Last edited by Wesley Snipes; 09-25-2010 at 01:19 AM.
Wesley Snipes is offline   Reply With Quote
Ads by Google

Guests, get your FREE E46Fanatics.com membership to remove this ad.