Window Switch LED Conversion

Following on from my IKE LED Conversion here is a DIY on how to change the window switches in your car to a different colour. This may have been done before, there may even be a DIY but i just did this as it was easy.

To remove the switches you need to remove the gaiter on your gear stick. Pinch it around the corners and lift it out to reveal the two screws holding the trim panel in place.




Remove the two screws at the back (closest to back of car) and lift it from here. There are 2 hinge like features at the front that as you lift will just lift out. Unclip the wires for your window switches and you end up with this.






The switch units simply unclip from the trim panel to give you this.


To remove the switch gubbins there are 3 little catches on each side to unclip. Shown here at the top of the unit. Just use a flat head screwdriver to pry it out.


This is what will come out.


Don't panic that the switch rockers have now gone 'limp', they are not broken this is fine. Also do not worry if a few bits fall out when you disassemble, this is also fine. The black plastic slider and grey rubber pads simply life up and off to reveal the LED and it's resistor. Note the orientation of the black plastic slider this has to go back the same way (won't go back wrong so you will know any way), the grey bit doesn't matter. Here is the LED.


Simply snip off or de-solder the existing LED and solder your new LED in its place. I used trial and error to get the anode and cathode (positive and negative) legs right as i couldn't tell which was which as the legs are already cut. Turn your cars lights on and just connect the switch to the wiring harness. If it lights up, bingo, if not swap it round.

Once that is done refitting is a reversal of removal.

***Tip - to put the switch back together rest both parts on their side. You can see on the side of the rocker (the bit you push with your finger) there is a grey plastic bit. Position this so that the bottom is level with the bottom of the switch housing (see pic). Being on its side the switches wont move while you slide the parts back together. This is where the orientation of the black plastic slider comes in. The bit that stands proud fits into the bottom of the rocker.***


Flash on:


Flash off:


Couple of other shots.

The LEDs were just standard 3mm LEDs by the way.

Nice

Thanks man. I'm slowly doing different parts of the interior lol. Next up is the steering wheel, then the LCM, HVAC controls and then stereo.

Thanks for the inspiration wooboodoo!!

I have made a RAR file of all the pictures i took during the job.

You can get it HERE.

If you don't have WinRar you can get that HERE.

Very Nice, Scott!

gaiter, n (plural gaiters)
1. A covering of cloth or leather for the ankle and instep; see spats
2. A covering cloth or leather for the whole leg from the knee to the instep, fitting down upon the shoe.
3. Part of the ecclesiastical garb of a bishop.

gubbins, n Informal
1. an object of little or no value
2. a small device or gadget
3. odds and ends; litter or rubbish
4. a silly person

Thanks for the feedback. Glad to see people think it's OK.

Gaiter:
•On a vehicle, a gaiter or boot refers to a protective flexible sleeve covering a moving part, intended to keep the part clean.

Gubbins:
•Something unspecified whose name is either forgotten or not known

Looks good. May I ask what's wrong with the amber color?

There was nothing 'wrong' with the amber colour. It worked OK but i just liked the idea of something a bit cleaner on the interior. I think once they are all white it will look even better. It had a lot to do with the fact i like to take things apart and put them back together and to make things unique. I don't know anyone near me who has a BMW with anything other than an orange interior

looks like good work...though i would never change to white...it looks like a honda now...but to each their own

Haha i never even knew Hondas were white! I have in my tool kit red, blue, green, white, yellow, orange and..... ultra violet. I thought the UV would look cool, for about 5 minutes, at which point i may decide i don't like it. I want something different to the stock colour but dont know what would be best. Do you think i could pull off UV?

looks awesom added to list of things to do this summer.

Thanks man hope it goes well.

wow!i've made the same but for the Window Switch for rear passenger...i have a sedan,and the rear switch aren't without leds...nice work!!

im having a hard time with the window switch its hard to get in there with my solder iron but i did the other ones myself with no problem

i tried the uv its not as bright and it come out too purple looking but i put them for my mood light and there they go nicely my iphone camara is not that great but thats the only button i tried with the uv im not too crazy about it

pics of the uv

the mood lights in uv i