E46 BMW Social Directory E46 FAQ 3-Series Discussion Forums BMW Photo Gallery BMW 3-Series Technical Information E46 Fanatics - The Ultimate BMW Resource BMW Vendors General E46 Forum The Tire Rack's Tire Wheel Forum Forced Induction Forum The Off-Topic The E46 BMW Showroom For Sale, For Trade or Wanting to Buy

Welcome to the E46Fanatics forums. E46Fanatics is the premiere website for BMW 3 series owners around the world with interactive forums, a geographical enthusiast directory, photo galleries, and technical information for BMW enthusiasts.

You are currently viewing our boards as a guest which gives you limited access to view most discussions and access our other features. By joining our free community you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is fast, simple and absolutely free so please, join our community today!

If you have any problems with the registration process or your account login, please contact contact us.

Go Back   E46Fanatics > Tuning & Tech > DIY: Do It Yourself

DIY: Do It Yourself
Post here to share or improve your wrench turning skills! All BMW E46 DIY tips, tales, and projects discussed inside. Learn to work on your car and know the right BMW parts you will need!

Reply
 
Thread Tools Search this Thread Rate Thread Display Modes
Old 03-19-2011, 04:56 AM   #1
mkodama
Registered User
 
mkodama's Avatar
 
Join Date: Oct 2006
Posts: 33,172
Review: Arcan 2-Ton Aluminum Service Jack ALJ2T

Sometimes, it is those little things in life that just make everything so much better. The Arcan jack in this review is one of those "little" things in my opinion among the plethora of options you have to lift your car.

Sure, you could use the little emergency jack in your trunk to lift the car for whatever project you are doing, but it takes forever spinning the handle while holding the jack in place, and that bit of an uneasy feeling putting the weight of your car on something so flimsy, especially on rough ground or if there is the slightest slope. I know this from initially doing a little work on my car this way. Besides, it's called an emergency jack for a reason.


Soon after I "upgraded" to an actual floor jack I bought from Kragen for $30 with included jackstands. Ok, not as much fear of the car dropping if the jack collapsed, but there were still many issues with this jack, like being hard to pump, annoying loose handle that you had to take out for lowering, needing to use the emergency jack to get my then lowered car high enough off the ground to even fit the Kragen jack, and then only being able to barely lift the car high enough to get the tires off the ground.


The years following, I had access to some of my first low-profile aluminum "racing" jacks of the 1.5-ton variety. They were other peoples' well used jacks, but I didn't have to pay to use them, so no complaints here. Now I was able to lift the car a further off the ground to a more practical height for doing more. The jack was similar to a Harbor Freight aluminum jack. Bare minimum, I would definitely go with one of these as it gets the job done, and a great value at $60 or less when they are on sale. In exchange for the great price and features though, was an all around crappy part. Lifting the car was still difficult, the lowering of the car was nice in that you didn't have to take out the handle to unscrew something, but if you weren't paying close attention you would drop the car instead of lowering it. Not surprisingly, in the end, the jack's quality showed even more. The rear wheels of the jack were attached with screws that perpetually loosened, which made the body of the jack drag on the ground, and make the jack unable to move if there was weight on it. The hydraulics worsened until the jack would barely lift, and the the funniest and scariest part was that one of the supports on the side of jack simply fell off. I have no clue how, but a good portion of the jack just fell off. This jack has since been retired.


After a few months of no Jack, forcing me to not doing any mods, I finally got an actual floor jack, and after the first time I used it, I knew what my automotive life has been missing all these years. Everything you could imagine about the jack is just about perfect. Sure, it does have some thickness to it, but at a lowered height 3.5" you can get under most anything. Once under the car, the jack lifts to a lofty 19.25", which is a significant ~5 inches above what the previous cheap aluminum "racing" jack could do. No need to worry about slipping with a cup shaped life point with a rubber pad inside that protrudes slightly to prevent any marring of underbody. Then there is actually using the jack. The hydraulics and motion of the jack are... orgasmic. Pulling down on the thick-walled and deeply knurled aluminum handle, and from vertical to horizontal it will pump fluid. There is very little effort needed, even though there is a significant amount of lift per pump. 3500 pound cars can be lifted with one hand and no bodyweight by an average person. With the 2000-3000 pound cars I deal with, the car goes up almost too easy, but I have no complaints because it still takes very few pumps to get to max height, and when you do get to max height, there is a heavy duty height limiter that prevents anything unsafe, and any extra pumps will return to the reservoir with a quiet hiss that you can feel through the handle. Safety wise, I don't think I could feel any safer. I still use jackstands for everything, but if the stands failed, I know the jack would hold the car and not tip. Size and weight wise, the jack is huge. It is much wider, longer, and made out of much thicker metal than cheaper "racing" jacks. A 1.5-ton Harbor Freight jack looks like a toy in comparison, and even though this jack is made out of nice anodized aluminum, it weighs in at 50 pounds. A bit on the heavy side for a jack, but I have no problem lifting the jack into the trunk of a car, and is light enough to whip around a concrete floor. A comparable sized steel jack, like Arcan's 3.5 ton steel jack on the other hand, is downright scary to pickup at over 115 pounds, and is heavy to even roll around. If your jack is so heavy that it is taxing to move around to where you need, you will be much less likely to use it. This 2-ton Arcan is light enough that I see myself using it for everything I can, most recently lifting a relatively light horizontal beam for constructing a storage rack. In conclusion, this jack is so nice that it will be worth more than it's $200 price tag to you. After 3 months of hard use, it still is bring a smile to my face every time I use it, when really for most of my stuff, I could have just lived with my emergency jack and cheapo Kragen jack.

If you are a true DIYer, give yourself a break, and reward your efforts with a quality Jack.


Brand: Arcan
Model: ALJ2T
Specs: http://www.arcanusa.com/lifting.html#
__________________


Last edited by mkodama; 03-19-2011 at 04:57 AM.
mkodama is offline   Reply With Quote
Ads by Google

Guests, get your FREE E46Fanatics.com membership to remove this ad.
Old 03-19-2011, 06:01 AM   #2
Beans562
Registered User
 
Join Date: Apr 2010
Location: Long Beach
Posts: 128
My Ride: 330i
Send a message via AIM to Beans562
nice, thanks for the review!
__________________
Beans562 is offline   Reply With Quote
Old 04-18-2011, 01:43 PM   #3
Hawker-rider
Registered User
 
Join Date: Mar 2009
Location: Florida
Posts: 20
My Ride: E46 325Ci
Ok,

That jack looks very good. But where can you buy them and for how much? The website doesn't offer much information, and some of the product links are not existent, that does not look very professional. I would like that info though.

good write up!
Hawker-rider is offline   Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Censor is ON





All times are GMT -5. The time now is 01:49 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
(c) 1999 - 2011 performanceIX Inc - privacy policy - terms of use