Lost Oil Pressure? Don't Lose Hope - E46Fanatics E46 BMW Social Directory E46 FAQ 3-Series Discussion Forums BMW Photo Gallery BMW 3-Series Technical Information E46 Fanatics - The Ultimate BMW Resource BMW Vendors General E46 Forum The Tire Rack's Tire Wheel Forum Forced Induction Forum The Off-Topic The E46 BMW Showroom For Sale, For Trade or Wanting to Buy

Welcome to the E46Fanatics forums. E46Fanatics is the premiere website for BMW 3 series owners around the world with interactive forums, a geographical enthusiast directory, photo galleries, and technical information for BMW enthusiasts.

You are currently viewing our boards as a guest which gives you limited access to view most discussions and access our other features. By joining our free community you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is fast, simple and absolutely free so please, join our community today!

If you have any problems with the registration process or your account login, please contact contact us.

Go Back   E46Fanatics > Tuning & Tech > Driveline, Engine & DME Tuning

Driveline, Engine & DME Tuning
Talk about driveline improvements, NA tuning and DME tuning your E46 BMW here. This includes diffs, intakes, exhausts, chips, software and OBD tuning.

Thread Tools Search this Thread Rate Thread Display Modes
Old 02-18-2012, 12:58 AM   #1
Registered User
Join Date: Aug 2008
Location: TN
Posts: 16
My Ride: 89 325is, 2002 325i
Lost Oil Pressure? Don't Lose Hope

I know with M5x and S5x engines there has been some documented issues with the oil pump nut backing off and causing loss of oil pressure and in most cases that include non-enthusiast drivers they continue to drive the car with the bright red oil dummy light on until the engine "starts actin' funny."

Now I am here to share my recent experience with a 2001 330i I purchased that had this exact problem to reassure those with similar issues that not all hope is lost.

If you were smart enough to shut your engine down as soon as the red oil light came on then kudus to you, simply repair your oil pump and keep truckin' but if you, your wife, gf, mom, previous owner were not so diligent then read on and be prepared to do some wrenching.


1. DO NOT attempt to repair the oil pump to restore pressure just to see how it will run. Most likely you have metal shavings setting on your bearing surfaces that will do more damage if you restore pressure and circulate them!

2. Perform a compression test. Healthy M54 compression should be at least around 180psi or greater.

3. If you have access to a boroscope then check the condition of your cylinder walls.

4. Drain all your oil and check for metal.

Here's where it begins to suck.

5. Pull your oil pan, remove the oil pump and windage tray.

6. Pull rod caps and main bearing caps to check for damage to bearing surfaces. If they are ok apply assembly lube and reinstall. Be aware that rod bolts are one time use so you will need to purchase new rod bolts. (My rod bearings were burned up but my main bearings were ok.)

7. Pull your valve cover and inspect your cam bearing surfaces / caps and lifters (In my case the bearing surface / caps 6 & 7 on the intake had completely scored up my intake cam shaft turning the caps black from the heat and cracking one in half not to mention just about all my lifters had collapsed.)

~ At this point if your compression test is healthy and you have not found any evidence of damage to any bearing surface or metal in your oil then wash down your valve train with a quart of fresh oil, repair your oil pump and button everything backup. Otherwise you have 2 choices. Replace the entire engine or rebuild it. (I chose to rebuild it)


8. Pull the cylinder head off the engine and at the very least have it cleaned in a parts washer to remove all metal shavings. Make note of any damaged parts and order replacements.

9. Remove the pistons and rods.

10. Purchase a 89mm Flex-Hone 240 Grit cylinder hone. Use this with a power drill to de-glaze your cylinder walls and restore crosshatching.

*Be sure to use hone oil or a light conventional oil and clean the bore many times with soapy water when you finish.

11. Install pistons with new rings, rod bearings, and rod bolts.

12. Reinstall your oil pump, windage tray and oil pan.

13. Reinstall your cylinder head using a new head gasket.

14. Assemble the remainder of the engine using new gaskets, seals, and orings. (This is also a good time to do other maintenance such as the oil filter housing gasket, VANOS seals, etc.)

15. In preparation for breaking in your new rings and bearings install a new oil filter and fill your crankcase with a conventional oil that has a high Zinc (ZDDP) content, (I used Shell Rotella T SAE 30).


This tends to be an issue that mechanics argue back and forth about. So here's my take.

16. Start your engine and allow it to warm up.

17. Rev your engine to 2-3k with a few 10-20 second revs to 5-6k in between for about 20-30 minutes.

18. Immediately change your oil and filter still using the same conventional oil you used for the initial break in.

19. After about 500 miles change your oil again to the synthetic oil of your choice.

20. Enjoy.

RobertK is offline   Reply With Quote
Ads by Google

Guests, get your FREE E46Fanatics.com membership to remove this ad.

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Censor is OFF

All times are GMT -5. The time now is 02:42 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
(c) 1999 - VerticalScope Inc. All rights reserved.