E46 BMW Social Directory E46 FAQ 3-Series Discussion Forums BMW Photo Gallery BMW 3-Series Technical Information E46 Fanatics - The Ultimate BMW Resource BMW Vendors General E46 Forum The Tire Rack's Tire Wheel Forum Forced Induction Forum The Off-Topic The E46 BMW Showroom For Sale, For Trade or Wanting to Buy

Welcome to the E46Fanatics forums. E46Fanatics is the premiere website for BMW 3 series owners around the world with interactive forums, a geographical enthusiast directory, photo galleries, and technical information for BMW enthusiasts.

You are currently viewing our boards as a guest which gives you limited access to view most discussions and access our other features. By joining our free community you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is fast, simple and absolutely free so please, join our community today!

If you have any problems with the registration process or your account login, please contact contact us.

Go Back   E46Fanatics > Tuning & Tech > DIY: Do It Yourself

DIY: Do It Yourself
Post here to share or improve your wrench turning skills! All BMW E46 DIY tips, tales, and projects discussed inside. Learn to work on your car and know the right BMW parts you will need!

Reply
 
Thread Tools Search this Thread Rating: Thread Rating: 12 votes, 5.00 average. Display Modes
Old 10-06-2012, 03:46 PM   #41
zwei e46
Registered User
 
Join Date: Jul 2009
Location: New Hampshire
Posts: 238
My Ride: '99 323i & '05 325xi
Thanks DenaliXTC

My issue was the 3 nuts securing the motor to the linkage were loose. The wipers worked, but I would get the occasional bang on the cowl. Finally got sick of it and this DIY helped me out big time. Once I got it out, the motor was barely hanging on to the linkage. Tightened/cleaned everything up and she's operates like she should.

Oh, and I agree, the hardest part was that @#*$*%! 10mm nut securing the linkage to the body. Very awkward location.

Thanks for taking the time and pics!
zwei e46 is offline   Reply With Quote
Old 03-23-2013, 05:18 PM   #42
tk1995
Registered User
 
Join Date: Aug 2007
Location: New Hampshire
Posts: 9
My Ride: 2004 325xi
Thanks for this tutorial. I tackled the repair today and it went very well. I think that the key is making sure the linkage is in optimal position before trying to take it out or put the new one in. One noteworthy item is I saw T27 screws mentioned but mine were T30. Here's another tutorial that was really helpful (I referenced both for my repair).

http://www.bmwserviceguides.com/e46-...-malfunctions/
tk1995 is offline   Reply With Quote
Old 06-12-2013, 01:20 PM   #43
Kurt597
Registered User
 
Join Date: May 2013
Location: Calgary
Posts: 8
My Ride: 330xi
Thank you for posting this! It was a great help for me when I was fixing my wiper motor. If anyone's wipers are still working but not properly i.e. they go down instead of up for the first cycle, it is completely fixable you do not need to buy a new motor.
Kurt597 is offline   Reply With Quote
Old 09-05-2013, 02:40 PM   #44
Hogan773
Registered User
 
Join Date: Jul 2009
Location: Chicago
Posts: 790
My Ride: 2002 325xi
I have a question and think I'm in the right thread.....

After the snow and ice one time last winter my wipers were all F-ed up and the wouldn't work, and then they would, and then they wouldn't. Finally they started working again on their own but now they stop about 10-15 degrees from the bottom. So basically when they turn on, they first sweep DOWN a bit and then go through the full arc and come to rest a little high on the windshield.

I'm assuming that under pressure, the linkage spline just slipped to an off-normal position and all I need to do is adjust it.

My question is, can I just get in there and loosen that connection where the motor attaches to the linkage, rotate the linkage slightly through its scissors motion till it gets to the right point, then tighten up that connection again WHILE STILL LEAVING THE WHOLE MOTOR AND LINKAGE INSTALLED IN THE CAR? I'd prefer not to have to reach in and find that hard to do 10mm nut, and pull the whole thing out, just to adjust the linkage by an inch or two. I know the motor will be stopped at what it thinks is the DOWN position, so rather than rotating the motor and all that, I'd think just moving the linkage to where it is scissored to its proper DOWN position and then tightening that spline nut would do the job?

Has anyone done this successfully? Or can you not loosen that spline nut without taking out the whole linkage? I'm trying to picture it based on the DIY and can't quite envision it.
Hogan773 is offline   Reply With Quote
Old 04-02-2014, 07:52 PM   #45
Gilbertofl09
Registered User
 
Join Date: Apr 2014
Posts: 1
This DIY saved me from all the guessing thanks for this, I bought a wiper switch thinking that went wrong but that wasn't it. I cleaned the wiper motor and it worked like new thanks again. Even though this is pretty late.


Sent from BimmerApp mobile app
Gilbertofl09 is offline   Reply With Quote
Old 04-12-2014, 12:57 PM   #46
Holomis
Registered User
 
Join Date: Feb 2014
Location: Victoria,Bc
Posts: 39
My Ride: 2000 323i
My wiper arm doesn't want to come off
Holomis is offline   Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Censor is ON





All times are GMT -5. The time now is 07:59 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
(c) 1999 - 2011 performanceIX Inc - privacy policy - terms of use