E46 BMW Social Directory E46 FAQ 3-Series Discussion Forums BMW Photo Gallery BMW 3-Series Technical Information E46 Fanatics - The Ultimate BMW Resource BMW Vendors General E46 Forum The Tire Rack's Tire Wheel Forum Forced Induction Forum The Off-Topic The E46 BMW Showroom For Sale, For Trade or Wanting to Buy

Welcome to the E46Fanatics forums. E46Fanatics is the premiere website for BMW 3 series owners around the world with interactive forums, a geographical enthusiast directory, photo galleries, and technical information for BMW enthusiasts.

You are currently viewing our boards as a guest which gives you limited access to view most discussions and access our other features. By joining our free community you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is fast, simple and absolutely free so please, join our community today!

If you have any problems with the registration process or your account login, please contact contact us.

Go Back   E46Fanatics > E46 BMW > E46 Convertible

E46 Convertible
The E46 vert forum. Talk about dropping your E46 top here.

Thread Tools Search this Thread Rating: Thread Rating: 12 votes, 5.00 average. Display Modes
Old 02-16-2013, 04:56 PM   #21
Registered User
Join Date: Jan 2011
Location: San Jose
Posts: 16
My Ride: 325CiC 2005
I replaced the roll over module today and the light on the cluster went out! Here's a couple of pointers for any other DIY'ers... The module is behind the right side rear seat. You need a 10 mm wrench to remove two bolts that hold the seat back in place. And you need a 13mm wrench to remove 4 hex bolts that secure the aluminum cover plate in the back of the seat. The roll over module hides behind that cover plate. And the module is secured by 3 special torx screws with a pin in the center of the torx hex socket. The tamper resistent torx screws require a special tool. I happened to have a folding assortment of those torx-with-a-pin wrenches, but it was barely long enough to reach. The screw in the bottom location is the hardest to see and get out. I recommend getting a longer reach specialty torx wrench for this job. The screws are tight due to loctite installed at the BMW factory. So it takes effort to unscrew them.

Of course you'll want the top down, and ensure the key is OFF, or the roll bars may deploy when you tild the module to remove it. I used blue loctite to reassemble.

After everything was back in place, I turned the key, started the car, and the dash light was off.

Some say I now need to get a code reader to reset the faults and register the new module. I may ask an indy to do that later. But Steven's Creek BMW wants $300 to do that...

Hope this helps...

Last edited by DTB; 02-16-2013 at 04:58 PM.
DTB is offline   Reply With Quote
Old 01-08-2015, 01:09 PM   #22
Registered User
Join Date: Jan 2015
Location: london
Posts: 6
My Ride: 320ci
Hi everyone need your help.

i drive e46 320ci 2002 convertible. car battery went dead and once it was replaced roll over protection light came on. i have a hard top on as its winters. roll over bars did not pop out but the light came on. i have checked the fuse and tried disconnection the battery again but no solution.
your help required in this matter.

thank you so much.
zainm is offline   Reply With Quote

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Censor is ON

All times are GMT -5. The time now is 05:36 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
(c) 1999 - 2016 performanceIX Inc - privacy policy - terms of use