What I've Learned About Stuck Exhaust Bolts - Page 3 - E46Fanatics E46 BMW Social Directory E46 FAQ 3-Series Discussion Forums BMW Photo Gallery BMW 3-Series Technical Information E46 Fanatics - The Ultimate BMW Resource BMW Vendors General E46 Forum The Tire Rack's Tire Wheel Forum Forced Induction Forum The Off-Topic The E46 BMW Showroom For Sale, For Trade or Wanting to Buy

Welcome to the E46Fanatics forums. E46Fanatics is the premiere website for BMW 3 series owners around the world with interactive forums, a geographical enthusiast directory, photo galleries, and technical information for BMW enthusiasts.

You are currently viewing our boards as a guest which gives you limited access to view most discussions and access our other features. By joining our free community you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is fast, simple and absolutely free so please, join our community today!

If you have any problems with the registration process or your account login, please contact contact us.

Go Back   E46Fanatics > E46 BMW > General E46 Forum

General E46 Forum
This is the place to get answers, opinions and everything you need related to your E46 (sedan, coupe, convertible and wagon) BMW!

Reply
 
Thread Tools Search this Thread Rating: Thread Rating: 94 votes, 4.79 average. Display Modes
Old 05-02-2015, 07:11 PM   #41
djdonis
Registered User
 
Join Date: May 2009
Location: Charlotte
Posts: 484
My Ride: e39 540i M, 330i 6sp
Quote:
Originally Posted by seaniekaye View Post
I am concerned about getting these apart... I need to take this all out to get to my guibo and center bearing. Despite all the praise for pb blaster, I think this could be a disaster.

They look in a very good shape despite all that rust buildup. Use rotary brush to clean them up a bit, soak them, then use impact wrench (find an electric one you could borrow, DeWalt or IR).
__________________
Diagnosis - BMW...

Last edited by djdonis; 05-02-2015 at 07:12 PM.
djdonis is offline   Reply With Quote
Old 05-05-2015, 06:22 AM   #42
timarnold
Registered User
 
Join Date: Feb 2013
Location: Maryland
Posts: 10
My Ride: 2005 X3
Quote:
Originally Posted by nleeumd View Post
So I am in the process of doing this now (car is on jack stands). I have a e46 330ci. I already sheered off one of the four studs right below the nut. Is it correct to assume that If I 'sheer' off the remaining three studs below the nut, the pipe should seperate from the header flange? Then i should proceed with the drill out method?
It should come apart with no problem after all 4 bolts are off. Heat is your friend and as mentioned if you have it, an induction heater is an excellent way of heating. I was never able to generate enough heat with a MAPP torch. You pretty much have to heat the studs up to cherry red.

Just buy a high quality drill bit (or 2) and do everything you can to get a good flat surface on which to drill.
timarnold is offline   Reply With Quote
Old 08-11-2015, 03:01 PM   #43
Archbid
Registered User
 
Join Date: Jun 2013
Location: Marin, CA
Posts: 1,542
My Ride: 2003 330cic
At this point in the lifespan of an e46, would it not be safe to say that your original flange bolts are likely gone?

I live in California and have a very well-maintained 330ci. The bolts and nuts were toast. I tried to get one off and it sheared instantly (with overnight PB Blaster).

Best to just not waste time and just get a good exhaust shop to torch them out, replace the gaskets, and start well.
Archbid is offline   Reply With Quote
Old 10-29-2016, 09:23 AM   #44
Streetthispgt
Registered User
 
Join Date: Nov 2008
Location: Toronto, ON
Posts: 46
My Ride: 2001 330ci
I recently had to go through the painful experience of drilling out the exhaust studs and just wanted to add to this thread. I decided to go this route as I didn't want to take the chance of an exhaust shop torching / impact hammering them out and potentially ruining the 02 sensors.

If you plan to drill, the easiest way to do this is cut the exhaust studs flush with the manifold so as to minimize the drilling distance. Do not drill all the way through. Drill until there is about 3-5mm of stud remaining at the end and use a round punch with a hammer to tap them out. At this point the stud with the head and whatever material there is remaining should fall out pretty easily. I've had good luck using a 23/64 Chicago latrobe 550 series drill bit (can be bought at grainger) for this job and found cheaper cobalt drill bits purchased at a regular hardware store just weren't up to the task for drilling these hardened studs out. Take your time, it should take about 45min of slow drilling per stud to get them out.

Photo of how the studs should look like after drilling and tapping them out:


Last edited by Streetthispgt; 10-29-2016 at 09:29 AM.
Streetthispgt is offline   Reply With Quote
Reply

Tags
broken, exhaust, exhaust bolts, header bolts, stuck

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Censor is ON





All times are GMT -5. The time now is 08:11 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
(c) 1999 - VerticalScope Inc. All rights reserved.