New Anyone in Denver Thread

Originally Posted by 325adam

Spacers are installed

20mm front
15mm rear

i hope you have extra long lugs or you installed long studs...


And yes, Cazz, May-7 is next open lapping day @ HPR (in fact, every Friday in May is an open lapping day).

Yeah, I put extra long bolts on there. ECS recommended 50 mm bolts up front and 45 mm in back.

Rich - I am putting some H&R race springs on next month. Can I mess with the camber on stock parts?

you probably should have gone with studs/nuts instead of bolts...
with bolts you never know how many threads of engagement you actually have.

also, 20mm is a LOT of spacer... be prepared to replace your wheel bearings in a year or two (unless you have some very high offset wheels).

Originally Posted by 325adam

Yeah, I put extra long bolts on there. ECS recommended 50 mm bolts up front and 45 mm in back.

Rich - I am putting some H&R race springs on next month. Can I mess with the camber on stock parts?

Not that much, but you could buy camber bolts that allow for more adjustment if you weren't getting suspension.

anyone need E46 airbags ?

i have pulled the steering wheel airbag and the front passenger airbag thus far.
door and a-pillar bags will come out at leisure OR when i have an interested party.

Thought you went back to the stock exhaust Garrett? Did you wire past the airbags, or are you going to stare at the light?

Spent 5 hours working on the 951 today. Got the momo steering wheel with quick release done, passenger airbag disconnected, airbag ECU defeated and horn wired up. Also ran wiring for the wideband and oil temp gauge...

well, i had to get rid of my RE exhaust since the tips were too large, as they were rubbing the trailer-hitch sides... went back to stock only while my custom exhaust was being fab'ed. now it's a chopped section-2 (just after the H-crossover and hanger) merge into single 3" back to a flanged muffler (flanged so that i can optionally hook up a straight-through pipe)... much lighter and no fitment interference with the trailer hitch.

i'll post some pics of it later... once it stops snowing/raining.

as for the airbags, the light has been on since i pulled the stock seats... so i don't care about the light.

ok so i thought id ask ya locals on this
i want alil more power on my ride but i dont have that much money for
forced induction. my budget would between 500-1500 i just want to get up to atleast 200hp
so far ive only got headers,intake,shark injector,exhaust and intake
Do ya have any suggestions on this???

You have a 325?

derp

red p?

justderplol

lol we're reading everything backwards!

!sdrawkcab gnihtyreve gnidaer er'ew lol

323 sadly

there's nothing wrong with that

Um you could do underdrive pulleys if you haven't already

Originally Posted by T330

justderplol

Originally Posted by nowerelsetoroam

323 sadly

ok, do you know how much power you are running now? or no? Do you want 200hp or 200rwhp?

200 at the wheels would be nice and no
i was thinking do a dyno once im done doing everything i want to it
i got told i could do nitrous but im not sure about that
and as for pulleys isnt there a crankshaft pulley for it?

Originally Posted by nowerelsetoroam

200 at the wheels would be nice and no
i was thinking do a dyno once im done doing everything i want to it
i got told i could do nitrous but im not sure about that

There are a lot of nitrous threads out there and DIY's. It looks fairly easy taking into account that you have the right tools. But, I feel its a little dangerous. You could possible do a 330 swap? I forget what Azzy spent, but hope you have a DD if you do that. You could also try getting a hight gear ratio. It doesn't get you any more power, but it will make you a little quicker. There isn't much power wise (to my knowledge) that you could do that doesn't require going into the internals.

i was thinking internals but 330 sounds good to i got a few miles in my engine
but if i were to go with the 330 would it really be better to put in a six speed?