|
|
|
|
||||||
|
General E46 Forum
This is the place to get answers, opinions and everything you need related to your E46 (sedan, coupe, convertible and wagon) BMW! |
 |
|
|
Thread Tools | Search this Thread | Rate Thread | Display Modes |
11-14-2012, 08:48 PM
|
#1 |
|
Registered User
|
Help needed ASAP!!
Hey guys I change both intake and camshaft sensor and took the exhaust solenoid to clean it up because I believe I had a stock solenoid because of p0340 code. And now my car suffer to start and it sounds like crap! Please I need some help ASAP!!!
Last edited by Mflara20; 11-15-2012 at 09:46 AM. |
|
|
|
11-14-2012, 09:54 PM
|
#2 |
|
Registered User
|
Cant see video but have you plugged it all fully? Have you made sure to mark the solenoid so u when you put it back it goes in thr exact spot where it was?
Sent from my X10a using Bimmer App
__________________
|
|
|
|
|
11-14-2012, 09:55 PM
|
#3 |
|
Registered User
|
Have u disvonnected any grounds? Messed with ur coils?
Sent from my X10a using Bimmer App
__________________
|
|
|
|
|
11-15-2012, 07:46 AM
|
#4 |
|
Registered User
|
I didn't mark the solenoids :.censor and I didn't messed with any cooks and I made sure I connect them tightly. What would happen if by accident I swap the solenoids?
|
|
|
|
|
11-15-2012, 09:48 AM
|
#5 |
|
Registered User
|
I fix the link, please I really need some help!
|
|
|
|
|
11-15-2012, 03:24 PM
|
#6 |
|
Registered User
|
Anyone
|
|
|
|
|
11-15-2012, 03:27 PM
|
#7 |
|
Registered User
|
did you go genuine bmw or aftermarket?
Last edited by scim459; 11-15-2012 at 03:27 PM. |
|
|
|
|
11-15-2012, 03:29 PM
|
#8 |
|
Registered User
|
So you replaced both intake and exhaust CPS's? Just wanted to clarify.
__________________
 |
|
|
|
|
11-15-2012, 03:33 PM
|
#9 |
|
Registered User
|
I replace both intake and camshaft sensors with aftermarket sensors from bavauto.
|
|
|
|
|
11-15-2012, 03:35 PM
|
#10 |
|
Registered User
|
And took out both solenoid to clean them up that's all I did. What I do wrong??
|
|
|
|
|
11-15-2012, 03:59 PM
|
#11 |
|
Registered User
|
put old sensors back on and see if it fixes this. if it is then you should just go genuine. im not sure about the solenoid issue.
|
|
|
|
|
11-15-2012, 04:03 PM
|
#12 |
|
Registered User
|
That's what I'm gonna do. But do you know anything about the solenoid issue?? Anyone???
|
|
|
|
|
11-16-2012, 07:16 AM
|
#13 |
|
Registered User
|
You should ve marked the location of the solenoid so u turn in to exact same spot. Now its too late,youll have to clear vanos adaptations and reset it so the solenoid reads correct data now. You need a proper bmw diagnostic software to do so. Ex, DIS ,Inpa
About the cam sensors,swap old ones in and check and from now on use only oem or oe parts for your bmw,no more china parts. Sent from my X10a using Bimmer App
__________________
|
|
|
|
|
11-16-2012, 09:00 AM
|
#14 |
|
Registered User
|
Do you know any good web page to buy the software from and the cable to connect my laptop to the car or do I have to go to my local stealership to fix it, or can rent the software from someone Im really desperate now.
Last edited by Mflara20; 11-16-2012 at 09:10 AM. |
|
|
|
|
11-16-2012, 09:16 AM
|
#15 |
|
Registered Gadfly
|
Not totally sure this will do it, but read through the thread and you'll find out. It's cheap.
http://forum.e46fanatics.com/showthread.php?t=893444
__________________
Engineers do it with a torque wrench
Last edited by Wolrab; 11-16-2012 at 09:17 AM. |
|
|
|
|
11-17-2012, 07:37 PM
|
#16 |
|
Registered User
|
Anyone??
|
|
|
|
|
| Thread Tools | Search this Thread |
| Display Modes | Rate This Thread |
|
|
Linear Mode
