Possible m54b30 into m54b25 - E46Fanatics E46 BMW Social Directory E46 FAQ 3-Series Discussion Forums BMW Photo Gallery BMW 3-Series Technical Information E46 Fanatics - The Ultimate BMW Resource BMW Vendors General E46 Forum The Tire Rack's Tire Wheel Forum Forced Induction Forum The Off-Topic The E46 BMW Showroom For Sale, For Trade or Wanting to Buy

Go Back   E46Fanatics > Tuning & Tech > E46 Engine Swaps

E46 Engine Swaps
Replacing your motor? From direct replacements to more exoctic engines, if it's going under the hood of an E46 3 Series this is the forum to discuss it.

Reply
 
Thread Tools Search this Thread Rate Thread Display Modes
Old 03-30-2020, 11:22 AM   #1
jdamore44
Registered User
 
Join Date: Jul 2013
Location: Port Angeles
Posts: 87
My Ride: '03 M3, '01 325xiT
Possible m54b30 into m54b25

Looking at possible HG failure. With the prices of B30's about the same as the b25 on ebay, I want to get the b30. I know that Coils are different after 02. What all do I need to consider when putting in a later m54b30?



Any advice on engine sellers?
Where is a good place to buy a reliable engine?
Thanks for any help guys!

Last edited by jdamore44; 05-19-2020 at 10:15 AM.
jdamore44 is offline   Reply With Quote
Old 04-04-2020, 05:59 PM   #2
Effduration
Registered User
 
Join Date: May 2017
Location: Boston
Posts: 813
My Ride: '05 330CiC
LKQ is a reputable seller of an engine...you might also call some of the independent BMW techs in your area.
One of the best, cheapest ways is to buy a running parts car with a B30 (e46, E39, X5, X3, etc) , compression test the engine, pull engine and part the rest..
Effduration is offline   Reply With Quote
Old 04-04-2020, 07:02 PM   #3
HayWagon
Registered User
 
Join Date: Jun 2017
Location: Collingwood Ontario
Posts: 1,289
My Ride: 03 330iT
I'd rather go to a local junkyard which will provide a warranty. Shipping and engine can expensive, especially considering how cheap B30s are.
Intake manifold, throttle body, disa, injectors, maf, upper and lower intake boots are all B30 specific. You can swap over your existing valve cover if you can't find one with the same coil style.
Flashing a MS43 to B30 spec is easy enough.
HayWagon is offline   Reply With Quote
Sponsored Links
Advertisement
 
Old 04-04-2020, 07:46 PM   #4
jdamore44
Registered User
 
Join Date: Jul 2013
Location: Port Angeles
Posts: 87
My Ride: '03 M3, '01 325xiT
I've found one at a junkyard that is a couple hours away that has 152k , he says he'll give me a 60 day warranty. $825 after taxes and core charge. I'm considering it..
jdamore44 is offline   Reply With Quote
Old 04-04-2020, 09:52 PM   #5
DTrentham
Registered User
 
Join Date: May 2018
Location: Illinois
Posts: 5
My Ride: 2001 330ci
Transmission: Manual
I have an 01 325ci that I swapped with a b30. Best decision I made. The b30 has so much more grunt and just moves the car so much better. I bought an entire e39 530i for super cheap that I just took everything off of to swap over, was quite easy. If you can find a b30 from an e46, even better. I'm not sure what parts you'd need and which are different cause I just swapped everything in between engines when I was doing it. Also depends on if your ms43 or not, if you are then its super easy to flash. Also if you have a manual and the donor is from an auto, don't forget the pilot bearing, I learned that the hard way! If you have anymore questions I would be happy to try and help.
DTrentham is offline   Reply With Quote
Old 04-05-2020, 12:58 PM   #6
jdamore44
Registered User
 
Join Date: Jul 2013
Location: Port Angeles
Posts: 87
My Ride: '03 M3, '01 325xiT
If I were to get a later motor, I could just use my IAT with the 3L intake manifold? My valve cover (and harness) and exhaust manifolds and 02 sensors? I would need to source an early Air intake and MAF? Also pulley ribs are different? Is that all? Then just flash as a 3.0L ms43 ?
jdamore44 is offline   Reply With Quote
Old 04-07-2020, 03:58 PM   #7
jdamore44
Registered User
 
Join Date: Jul 2013
Location: Port Angeles
Posts: 87
My Ride: '03 M3, '01 325xiT
Here is a link to a video of an engine for sale near me. It has 140K on it. What do you guys think?
https://photos.app.goo.gl/nbSkcX2TR93B2TGV8

and the other one he has for sale (120K)
https://photos.app.goo.gl/CZ8jXr241gtSDMxCA

The 140K seemed to sound better to my untrained ear.

Last edited by jdamore44; 04-07-2020 at 05:32 PM.
jdamore44 is offline   Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Censor is OFF



All times are GMT -5. The time now is 04:51 AM.


Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2020, vBulletin Solutions, Inc.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
(c) 1999 - VerticalScope Inc. All rights reserved.